Best Barns riviera_1212df Instrukcja Obsługi

Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright

Step 10 Assemble Front Wall Frames Continued1. Locate the components as shown in diagram below.2. Install the top 72" long 2x4 and bottom 66-1/2&

Step 11 Set Walls1. Secure wall panels together at the corners. Use (4) four 10d coated nails per corner. Nail wallpanels to wood floor. Nail through

1. Install a 46-1/2" long 2x6 on the sidewall. Butt up topreviously installed 72" tie plate on side wall. The 2x6will protrude through the f

3/4" SpaceGable Siding Reston Filler3/4" SpaceStep 14 Install Rear Roof GableImportant: Bottom edge ofsiding extends over 1x4 trim.Paint thi

Detail 'D'4. Place reference marks 49" from the peakof the trusses on both sides. These markswill be used when installing the first row

Optional ridge vent providesideal ventilation.AirSpaceTrussShinglesInstall This Row FirstStep 16 Install Roof Sheathing1. Install roof sheathing per l

Locate (4) four 96" long 2x4's with angled cuts at both ends, (2) two 10-1/8" wide x26-1/2" long and (2) two 9" wide x 62-1/2

1. Install a 20" x 15" plywood decorative board at the top of thefront gable, flush with the top of the roof sheathing. Use 8d galv.nails.2.

3. Install 59-1/8" long 1x4 trim boards atthe front wall corners, flush with the sidingon the sidewalls.4. Install 59-1/8" long 1x4 trim boa

Step 21 Install Doors & Hardware4. Before you fasten the hinges to the doortrim, temporarily prop the doors in theopening. Leave a space at the to

Tongue EdgeLAP EdgeIMPORTANT INFORMATION ABOUT YOUR SHED KITTool ListHammer & Hand SawFraming Square & LevelPower Circular SawPower Drill/scre

Material Packaged In Component Kit2 ea. Pre-built Walls 48" x 78-1/4"2 ea. Pre-built Walls 21" x 78-1/4"1 ea. 12" x 20"

12' - 0" Building WidthTo keep 2x4 frame frommoving, toe nail to 4x4.XXXXXX16"15-1/4"2x4 Joist HeaderXX16"Shown below is a ty

When measurements are given for a boardlength or width, it is from the longest side.measure from hereStep 1 Assemble Trusses1. Screw (2) two 2x4 block

center lineStep 2 Assemble Roof Gables1. Butt (2) two 52-1/2" long 2x4s together andsecure by nailing a 3-1/2" x 44" long plywoodgusset

AABBXXXXXXXXXXXXBAStep 4 Install Siding on Gables1. Select one of the gable frames, Turn the gable over letting the bottomplate overhang the floor so

1. Square wall frame. Measure diagonally (corner to corner). The measurementswill be the same when the wall is square.2. Install a 36" long 2x6

1. Square wall frame. Install a 36" long 2x6 board on the right end of the wall frame.The plate needs to extend 3-1/2" past the end of the w

1. Locate (2) two 48" long 2x4s.2. Install (3) three 2x4-74-1/2" wall studs betweenthe boards. Install third stud in the center of thewall f