Best Barns woodville1012 Instrukcja Właściciela

Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright

Step 8 Assemble Front Wall Panels1. Install (6) six 72" wall studs between 2x4 - 10' top and bottom plates.2. Cut (2) two 2x4-6' board

Step 8 Assemble Front Wall ContinuedSiding ExtendsBelow HeaderCut EdgeButt Square EdgesTogetherCut EdgeTongue EdgeLAP Edge5. Locate a 16" x 77-1/

Step 9 Set Lower WallsStep 10 Install Trim3. Install 1x4x74-3/4" trimboards at the corners ofthe front wall.4. Install lx4x72" boards along

Step 11 Install Rear Gable3. Install the rear gable on the back wall. The gable siding will extend over the 1x3 trim onthe lower wall. NOT behind the

3. Using 1-1/2" hanger nails, install the right hangers to the 2x6 tie plate.The top hanger flange should line up with the 'X' mark.Woo

2' x 4' OSB4' x 4' OSB2' x 4' OSB1. Install the trusses over the 'X' marks. Installhanger to the opposite side

10'x12'10'x16'Building LengthRoof Shingles 7 bdl. 10 bdl.Roof 'drip' Edge 6 pcs. 7 pcs.Material DescriptionBuilding Tip:

3. Cut and install a 2x3 block toclose off the opening at thebottom of the overhang.Step 15 Install Gable Overhang1. While a helper holds the 47"

Step 17 Install Doors & Hardware4. Before you fasten the hinges to the doortrim, temporarily prop the doors in theopening. Leave a space at the to

Roof Materialby OwnerRoof Shingles 7 bdl.Roof 'drip' Edge 6 pcs.Woodville 10'x 12' Barn kit Packing ListQty. Qty.4 Wall Plates 120

Tongue EdgeLAP EdgeTool ListHammer & Phillips ScrewdriverFraming Square & LevelHand or Circular SawAlways wear safety glasses when cutting or

10' - 0" Building WidthNail the 2x4s to the 4x4runners to keep the 2x4frame from moving.It is important that the floor belevel and square. B

Wood Gusset with 2x4 BlockStep 1 Assemble Trusses2x4 Truss Half2x4 BlockTop GussetLower Gusset2x4-116-1/4" Bottom Cord1. Position (2) two half tr

Siding Extends3/4" Below PlateTip; Lay 2'x4' OSB sheathing under thestuds to prevent gable studs from beingknocked loose when nailing t

Siding Extends3/4" Below PlateStep 3 Assemble Front Gable1. Assemble another gable frame. Install a 36" long 2x4 between the wallstuds. If i

4. Assemble the loft doors. The loft door frames aretemporarily held together with corrugated fasteners,this is the back side of the door frame. Place

Step 6 Assemble Back WallSiding Extends 3/4" Below PlateCut EdgeLAPTongue EdgeTop PlateWall Stud3-1/2"56-1/2" Tie Plate56-1/2" Tie

9. Repeat steps to assemble another sidewall.AABBXXXXXXXXXXXXStep 7 Assemble Sidewalls1. Position 68-1/2" and 65-1/2" long 2x4 boards togeth